P103 Short Stroke Linear Position Sensor

P103 Short Stroke Linear Position Sensor The P103 is a durable, affordable, high accuracy short stroke linear inductive position sensor designed for use in industrial and scientific applications. The P103 is very compact and offers an excellent stroke to overall length ratio. Each unit is supplied calibrated to the exact travel required by […]

P103 Short Stroke Linear Position Sensor

The P103 is a durable, affordable, high accuracy short stroke linear inductive position sensor designed for use in industrial and scientific applications.
The P103 is very compact and offers an excellent stroke to overall length ratio. Each unit is supplied calibrated to the exact travel required by the customer, for example, if your application requires 1″ (25 mm) measurement then Positek will manufacture the sensor specifically for this length.The mechanical length and calibration will be set up for 25mm. The P103 is available with any travel from 10mm to 50mm..

The overall performance, repeatability and stability are outstanding over a wide temperature range. The sensor has a rugged stainless steel body and plunger.
The P103 sensor is particuarly easy to install with either flanged housing or body clamps. The plunger can be supplied captive or free with either female M4 thread or spring loaded with dome end. The P103 is available with a wide range of electrical inputs/outputs, sealing up to IP65/IP67 dependant on connector/cable options and fully integrated EMC protection.

The Full Positek Range Also Offer a range of Intrinsically Safe and ANZEx approved to Ex ia I/IIC T4

Intrinsically Safe systems provide a safe operating environment for personnel and equipment. Intrinsic Safety (IS) is based on the principle of restricting the  electrical energy transmitted into a hazardous area, thereby ensuring that any sparks or heated surfaces that may occur as a result of electrical failures are insufficient to cause ignition. The threat of an explosion is eliminated.

Positek’s ATEX and IECEx approved Intrinsically Safe sensors can be used in hazardous environments when connected to our approved galvanically isolated amplifier. Positek offers Intrinsically Safe sensors for the following three hazard classifications:

  • ‘A’ Series ANZEx Approved Intrinsically Safe Sensors for Gas/Vapour, Dust and Mining.
  • ‘X’ Series Sensors Position Sensors for use in potentially explosive gas/vapour atmospheres.
  • ‘E’ Series Sensors Position Sensors for use in potentially explosive gas/vapour and dust atmospheres.
  • ‘M’ Series Sensors Position Sensors for use in potentially explosive gas/vapour, dust and mining environments.

ATEX logoiso 9001:2000 logoIECEx

Positek sensors are now available in the EX07 versions which are ATEX and IECEx

Qualified to Intrinsic Safety Specification

  • II 1 GD
    I M1
    Ex ia IIC T4 Ga
    Ex ia IIIC T135°C Da
    Ex ia I Ma
    Ta = -40°C to 80°C
  • Certificate number Sira 13ATEX2371X and IECEx SIR 13.0154X
  • The ambient temperature rating is extended to -40°C to 80°C.

The sensors must be used with a galvanically isolated three port amplifier
designed to supply the sensor with a nominal 5V and to transmit the buffered
output to a safe area.

The Positek X005 Galvanic Isolation Amplifier designed specifically for use with Positek Intrinsically safe sensor range is available in the following output options:

0.5 to 9.5V X005-545
9.5 to 0.5V X005-546
4 to 20mA X005-425
20 to 4mA X005-426

 

Dimensions
Body Diameter 35mm
Body Length (Flanged) Measurement length 71.3mm
Body Length (Unflanged) Measurement length 55mm
Push Rod Outside Diameter 6mm
Travel any stroke from 10 mm to 50mm (eg 35mm)
Independant Linearity <±0.25% at 20°C
Temperature Coefficient <±0.01%/°C Gain & <±0.01%FS/°C Offset
Resolution Infinite
Noise <0.02% FSO
Frequency Response >10KHz (-3dB);
>300Hz (-3dB); 2 wire 4-20mA
Output Signal and Output Load
Output Signal Output Load
0.5 to 4.5 V dc ratiometric 5K Ohms min
0.5 to 4.5 V dc 5K Ohms min
± 5V dc 5K Ohms min
± 10V dc 5K Ohms min
0.5 to 9.5 V dc 5K Ohms min
4 to 20mA (2 wire) 300 Ohms @ 24V
4 to 20mA (3 wire sink) 950 Ohms @ 24V
4 to 20mA (3 wire source) 300 Ohms Max
Supply Current
12 mA Typical 20 mA max. (Voltage Versions)
Temperature Limits
Operating -40 to 125°C (5V input only)
-20 to 85°C
Storage -40 to 125°C
EMC Performance
Susceptibility EN 61000-6-2
Radiated EN 61000-6-3
Vibration IEC 68-2-6: 10g
Shock IEC 68-2-29: 40 g
MTBF 350,000 hrs 40°C Gf
Sealing IP65(connector) / IP67(cable)
Electrical Connections Screened 3 core cable or integral connector
Dimensions
Body Diameter 35mm
Body Length (Flanged) Measurement length 71.3mm
Body Length (Unflanged) Measurement length 55mm
Push Rod Outside Diameter 6mm
Travel any stroke from 10 mm to 50mm (eg 35mm)
Independant Linearity <±0.25% at 20°C
Temperature Coefficient <±0.01%/°C Gain & <±0.01%FS/°C Offset
Resolution Infinite
Noise <0.02% FSO
Frequency Response >10KHz (-3dB);
>300Hz (-3dB); 2 wire 4-20mA
Temperature Limits
Operating -40 to 125°C (5V input only)
-20 to 85°C
Storage -40 to 125°C
EMC Performance
Susceptibility EN 61000-6-2
Radiated EN 61000-6-3
Vibration IEC 68-2-6: 10g
Shock IEC 68-2-29: 40 g
MTBF 350,000 hrs 40°C Gf
Sealing IP65(connector) / IP67(cable)
Electrical Connections Screened 3 core cable or integral connector