SST20 Inclinometer

  SST20 Inclinometer SST20 inclinometer based on Vigor’s advanced tilt measurement technology, to meet with low cost, high reliability and volume application, performs high performance-cost ratio. SST20 employed most universal & mass-produced components, casting aluminum alloy house, universal high reliability M12-5pin industrial connector; full epoxy seal with IP69K protection, auto-test/calibration […]

 

SST20 Inclinometer

SST20 inclinometer based on Vigor’s advanced tilt measurement technology, to meet with low cost, high reliability and volume application, performs high performance-cost ratio.
SST20 employed most universal & mass-produced components, casting aluminum alloy house, universal high reliability M12-5pin industrial connector; full epoxy seal with IP69K protection, auto-test/calibration equipment which not only ensure delivery speed, also keep the consistency of goods.
Thanks for Vigor engineers, they adopt advanced technologies as:0
– CAE/EDA simulation;
– Modal test for both housing and PCB to eliminate resonance due to vibration;
– Comprehensive performance & function test for component & firmware;
– Calibration technology based on SST300 high accuracy inclinometer;
– Refer MIL/ EN/ ISO/IEC standards to enhance SST20 durability & reliability.
SST20 support remote diagnosis without disassembling. MTBF more than 10 years per time. Can work in 10m submersible depth long time and has better EMC ability.
SST20 output RS485/CAN/CANOpen and Voltage/Current signals. Better power management to meet with automotive /truck/vehicle application without regulated power.
OEM service is available with calibrated PCBA or MIL qualified.

Features

– Low cost, high performance, suitable for batch application
– 50Hz refresh rate, 10Hz response frequency
– ±0.07°accuracy@-15~50℃
-±0.2% cross-axis error
– Available to horizontal, vertical, headstand, etc installation methods

– IP67protection
– 9~36VDC power supply
– Sensing elements survive to 1500g shock while operating

Applications

Vessel, Engineering machinery, Solar/wind energy, automobile/truck/vehicle, Communication/electric Tower monitoring, High-voltage pylon monitoring, Antenna, construction engineering, Landslide, etc

 

 

Output Interface RS232/RS485/CAN/CANOpen/Switch 0.5~4.5VDC/4~20mA
Measurement range ±5°、±10°、±15°、±30°、±45°、±60°、±90°、±180°、0~360°
Accuracy ±0.07°@-15~50℃ ±0.15°@-15~50℃
Non-linearity ±0.03° ±0.05°
Resolution 0.002° 0.005°
Repeatability ±0.02° ±0.05°
Offset ±0.02° ±0.05°
Cross-axis sensitivity ±0.2%FS ±0.2%FS
Measuring axis 1 or 2 axis（±180°and 0~360°measurement range single axis only）
Bandwidth Default 3Hz，5Hz、10Hz available
Response time 5ms（no filtering） 10ms（no filtering）
Refresh rate Default 5Hz，max. 50Hz 50Hz
Cold start warming time Less than 60s
Interface features RS232: 9600bps (adjustable), 8 data bits, 1 start bit, 1 stop bit Voltage output: 0.5~4.5VDC; Internal resistance 0.3Ω; Drive current (max.) 15mA
RS485: 9600bps (adjustable), 8 data bits, 1 start bit, 1 stop bit No matched resistance
CAN2.0: according to ISO11898-2 standard, 40k~1MBit/s baud rate, adaptive standard frame and extended frame format No matched resistance
CANOpen: according to DS301 standard, 40k~1MBit/s baud rate No matched resistance Current output: 4~20mA; Internal resistance 50MΩ; load impedance 150~650Ω
Switch output: Darlington OC output, load with1A @9～36VDC, alarm point can be pre-set in factory
Power consumption RS232/RS485 Output: 9~36VDC, current ≤50mA@24VDC 16~36VDC current≤30mA（no-load）@24VDC
CAN/CANOpen Output: 9~36VDC, current≤80mA@24VDC
Switch output: 9~36VDC，current≤50mA（no-load）@24VDC
Operation temperature range -40～85℃
Storage temperature range -40～85℃
EMC According to EN 61000/GBT17626
Insolation ≥100MΩ
MTBF 10 years
Shock 100g@11ms, three-axis, half- sine
Vibration 8grms，20～2000Hz
Protection IP67
Connector M12 5-Pin socket
Weight ≤200g (no connector or cable)

 

No Information Available.

Operation temperature range -40～85℃
Storage temperature range -40～85℃